l IDENTIFICATION

Appearance & Odour: Brown solid. Characteristic pungent odour.
Melting/softening point: Decomposes before melting.
Boiling point and vapour pressure: Not applicable.
Volatile materials: No specific data. Expected to be low at 100°C.
Flashpoint: Does not burn.
Specific gravity: No data.
Solubility in water: Forms suspensions.
Corrosiveness: Not corrosive.

Ingredients

Health Effects:
No specific data is available for the product for chronic exposure symptoms. The ingredients are not listed as carcinogenic in Worksafe’s document "Exposure Standards for Atmospheric Contaminants in the Occupational Environment" (May 1995).

Acute Effects:
Swallowed: Data suggests that this product should present no significant problems to typical persons if used as intended.
Eye: Data suggests that this product should present no significant problems to typical persons if used as intended.
Skin: Data suggests that this product should present no significant problems to typical persons if used as intended.
Inhalation: Data suggests that this product should present no significant problems to typical persons if used as intended.

First Aid:
If this product gets into mouth, wash out with water. No further measures should be necessary.
Eyes: If product gets in eyes, wash eyes to remove material. No further measures should normally be required.
Skin: If product gets on skin, wash skin to remove material. No further measures should normally be required.
Inhalation: No first aid measures normally required. However, if vapours or dusts have been inhaled, and irritation has developed, remove to fresh air and observe until recovered. If irritation becomes painful or persists more than about 30 minutes, seek medical advice.
Advice to Doctor: Treat symptomatically. Note the nature of this product.

_____________________________________________________________________________________________________________________

Exposure Standards:
A time weighted average (TWA) concentration for an 8 hour day, and 5 day week has not been established by Worksafe Australia for any of the major ingredients in this product. There is a blanket limit of 10mg/m³ for dusts or mists when limits have not otherwise been established. The nature of this product makes it unlikely that this level will be approached in normal use.

Engineering Controls:
In industrial situations, concentration values below the TWA value should be maintained. Values may be reduced by process modification, use of local exhaust ventilation, capturing substances at the source, or other methods. If you believe air borne concentrations of mists, dusts or vapours are high, you are advised to modify the process or environment to reduce the problem.

Personal Protection:
Respiratory Protection: It is usually safe to not use a dust mask or respirator protection on account of this product. However, if the product is being used in dusty or confined conditions, use of a mask or respirator may be preferred. For help in selecting suitable equipment, consult AS/NZS 1715.
Protective Gloves: Protective gloves are not normally necessary when using this product. However, it is always prudent to wear gloves. For help in selecting suitable equipment, consult AS 2161.
Eye Protection: Protective eyewear is not normally necessary when using this product. However, it is always prudent to use protective eyewear. Consult AS1336 and AS/NZS 1337 for advice on Industrial Eye Protection.
Clothing: This product is essentially safe to use without special protective clothing. However, its use is recommended as a good industrial practice. Consult AS2919 for advice on Industrial Clothing.
Safety Boots: Wearing safety boots in industrial situations is advisory. Consult AS/NZS2210 for advice on Occupational Protective Footwear.
Always wash hands before smoking, eating or using the toilet. Wash contaminated clothing and other protective equipment before storing or re-using

__________________________________________________________________________________________________________________________

Storage & Transport
No special storage and transport requirements. This product has no UN classification. Not a Scheduled Poison. Containers should be kept closed in order to minimise contamination. Keep from extreme heat and open flames, and make sure that the product does not come into contact with substances listed under "Materials to avoid" below.

Spills & Disposals
Minor spills do not normally need any special cleanup measures. In the event of a major spill, prevent spillage from entering drains or water courses. No special protective clothing is normally necessary. However use judgement and take care. Stop leak if safe to do so, and contain spill. Sweep up and shovel or collect recoverable product into labelled containers for recycling or salvage. After spills, wash area preventing runoff from entering drains. If a significant quantity of material enters drains, advise emergency services. Full details regarding disposal of used containers, spillage and unused material may be found on the label. If there is any conflict between this MSDS and the label, instructions on the label prevail. Dispose of only in accord with all regulations.

Fire & Explosion Hazard
There is no risk of an explosion from this product under normal circumstances if it is involved in a fire.
Flashpoint: Does not burn.
Flammability limits: Not applicable. This product does not burn.
Extinguishing Media: This product does not burn. Use extinguishing media suited to the materials that are burning. carbon dioxide, dry chemical, foam, water fog.
Special Fire Fighting procedures: When fighting fires involving significant quantities of this product, wear safety boots, non-flammable overalls, gloves, hat, goggles and respirator. All skin areas should be covered.
Unusual Fire & Explosion Hazards: Fire decomposition products from this product may form toxic and corrosive mixtures in confined spaces.
Stability: This product is unlikely to spontaneously decompose.
Polymerisation: This product is unlikely to spontaneously polymerise.
Decomposition Products: Carbon dioxide, and if combustion is incomplete, carbon monoxide and smoke. Nitrogen, and under some circumstances, oxides of nitrogen and sulfur. Water.
Materials to avoid: strong oxidising agents.

_____________________________________________________________________________________________________________________________